Sign In / Register
View Cart / Checkout
Current Filters
Remove all filters
More Filters:
Most Popular
Body Jewelry
Other
Shirt sizes
Ring sizes
Ear
Nose
Other
Face
Genital
Clearance Clearance Bin (Invictus Labret, Straight, Curved and Circular Barbells)
Clearance Bin (Invictus Labret, Straight, Curved and Circular Barbells)
Main Photo
10% OFFSavings: Retail
Qty
Sold as a SINGLE
$ USD

These items are being clearanced not because they are flawed,
but because we ordered or were sent the incorrect items and do not
intend to carry these as stock. Please enjoy the savings on these first
quality pieces!

This page has both internally threaded and threadless items.  Each item is marked as such.

Items are sold as single not in pairs, unless specified in the drop down menu.

  •  HP = high polish titanium
  • Ti = Titanium

If you have a question on an item, please contact customer service and we will get you taken care of.

About threadless jewelry
Threadless jewelry is a push pin technology. The removeable end (dark grey) has a slightly curved pin. This pin straightens out when inserted into the shaft (light grey). The resulting spring tension force holds the two pieces together securely.

  • STEP 1 - Insert the pin about halfway into the shaft.
  • STEP 2 - Bend the pin SLIGHTLY by hand as shown. For a tighter fit bend the pin more. For an easier fit straighten the pin out a little.
  • STEP 3 - Push in the removable end to close.
  • STEP 4 - To remove, pull apart both ends. If the jewelry is tight, add a slight twisting motion while you pull out the removable end.
In our drop-down menus for adding to cart, we show the gauge of the item you are ordering, then the length/diameter, then the ball size if it has any:

Jewelry is measured through a gauge system (see chart below). The higher the gauge number the smaller the wire is. A standard "earring" is usually 20 gauge. Jewelry gauges/sizes can vary between manufacturers. There is no universal regulation on companies to make a standard size in body jewelry. A big part of this is that some jewelry is made overseas and measured in millimeters. And in the USA jewelry is measured in inches/gauges. So many times jewelry can be anywhere from .5mm to 1mm different.

CONVERSION CHART:
Gauge Millimeter Inch
16g 1.2mm 3/64"
14g 1.6mm 1/16"
12g 2mm 5/64"
10g 2.4mm 3/32"
8g 3.2mm 1/8"
6g 4mm 5/32"
4g 5mm 3/16"
2g 6mm 1/4"
0g 8mm 5/16"
00g 9mm to 10mm 3/8"
  11mm 7/16"
  13mm 1/2"
  14mm 9/16"
  16mm 5/8"
  19mm 3/4"
  22mm 7/8"
  25mm 1"
  26.9mm 1-1/16"
  28.5mm 1-1/8"
  30.1mm 1-3/16"
  31.7mm 1-1/4"
  33.3mm 1-5/16"
  34.9mm 1-3/8"
  36.5mm 1-7/16"
  38.1mm 1-1/2"
  39.6mm 1-9/16"
  41.2mm 1-5/8"
  44.4mm 1-3/4"
  47.6mm 1-7/8"
  51mm 2"
Measuring septum jewelry
Septum jewelry is measured by the diameter straight across the center of a ring. How far it sits below your nose will be dependant on where you're pierced. We've given an example below of a septum that's pierced a bit lower (see the side shot) and how it will look with different diameters. The general rule is, the smaller the diameter the tighter the fit.
5/16" (~8mm) diameter
3/8" (~10mm) diameter
1/2" (~12mm diameter)
Enlarged example of 1" on ruler
Ruler example