Current Filters
More Filters:
Most Popular
Body Jewelry
Other
Shirt sizes
Ring sizes
Ear
Nose
Other
Face
Genital
Limited 14K Gold Constellation Threadless End
LIMITED
Qty
Sold as a SINGLE
$ USD
As brilliant as the stars in the night sky, these constellation ends are a beautiful addition to any jewelry collection!

This end will fit most of these posts that are 18g/16g/14g.

All measurements are approximate:

  • The Pisces end measures 10.8mm tall by 9.3mm wide, and is set with four 1.5mm gems and one 2mm gem. The threadless pin is one the back of the second gem down.
  • The Lynx end measures 4.4mm tall by 14.2mm wide, and is set with three 2mm gems and one 3mm gem. The threadless pin is one the back of the second gem down.
  • The Virgo end measures 8.9mm tall by 6.7mm wide, and is set with four 2mm gems. The threadless pin is set at the top of the triangle.
  • The Cassiopeia end measures 6.6mm tall by 12.1mm wide, and is set with four 2mm gems, and one 3mm gem. The threadless pin is set on the back of the 3mm gem.
  • The Aries end measures 5.1mm tall by 16.3mm wide, and is set with three 2mm gemss and one 3mm gem. The threadless pin is set on the back of the 3mm gem.
  • The Ursa Major end measures 5.6mm tall by 17.5mm wide, and is set with eight 1.5mm gems. The threadless pin is set on the back if the second gem down from the top of the square.
  • The Capricorn end measures 10mm tall by 13.1mm wide, and is set with five 2mm gems and one 3mm gem. The threadless pin is set on the back of the 3mm gem.
  • The Super Nova end measures 8mm tall by 16mm wide, and is set with one 4mm center gem and the four bottoms are 3.5mm. The threadless pin is set on the back of the 4mm gem.
  • The Cygnus end measures 10.5mm tall by 16.6mm wide, and is set with one 4mm center gem and the six bottoms are 3mm. The threadless in is set on the back of the 4mm gem.
  • The Summer Triangle end measures 4.5mm tall by 4.5mm wide, and is set with three 1.5mm gems. The threadless pin is set at the top of the triangle.
  • The posts are made from implant grade stainless steel
About threadless jewelry
Threadless jewelry is a push pin technology. The removeable end (dark grey) has a slightly curved pin. This pin straightens out when inserted into the shaft (light grey). The resulting spring tension force holds the two pieces together securely.

  • STEP 1 - Insert the pin about halfway into the shaft.
  • STEP 2 - Bend the pin SLIGHTLY by hand as shown. For a tighter fit bend the pin more. For an easier fit straighten the pin out a little.
  • STEP 3 - Push in the removable end to close.
  • STEP 4 - To remove, pull apart both ends. If the jewelry is tight, add a slight twisting motion while you pull out the removable end.
    THIS IS A LIMITED ITEM! Limited jewelry is usually re-stocked much less frequently and is harder for us to get from the manufacturer. So get it while you can, while it's available!
In our drop-down menus for adding to cart, we show the gauge of the item you are ordering, then the length/diameter, then the ball size if it has any:

Jewelry is measured through a gauge system (see chart below). The higher the gauge number the smaller the wire is. A standard "earring" is usually 20 gauge. Jewelry gauges/sizes can vary between manufacturers. There is no universal regulation on companies to make a standard size in body jewelry. A big part of this is that some jewelry is made overseas and measured in millimeters. And in the USA jewelry is measured in inches/gauges. So many times jewelry can be anywhere from .5mm to 1mm different.

CONVERSION CHART:
Gauge Millimeter Inch
16g 1.2mm 3/64"
14g 1.6mm 1/16"
12g 2mm 5/64"
10g 2.4mm 3/32"
8g 3.2mm 1/8"
6g 4mm 5/32"
4g 5mm 3/16"
2g 6mm 1/4"
0g 8mm 5/16"
00g 9mm to 10mm 3/8"
  11mm 7/16"
  13mm 1/2"
  14mm 9/16"
  16mm 5/8"
  19mm 3/4"
  22mm 7/8"
  25mm 1"
  26.9mm 1-1/16"
  28.5mm 1-1/8"
  30.1mm 1-3/16"
  31.7mm 1-1/4"
  33.3mm 1-5/16"
  34.9mm 1-3/8"
  36.5mm 1-7/16"
  38.1mm 1-1/2"
  39.6mm 1-9/16"
  41.2mm 1-5/8"
  44.4mm 1-3/4"
  47.6mm 1-7/8"
  51mm 2"
Enlarged example of 1" on ruler
Ruler example