Hand Carved Organic Designs in Horn, Bone and Shell
Advanced search & filters
Current Filters
More Filters:
Body Jewelry
Regular Jewelry
Other
Shirt sizes
Ring sizes
Ear
Nose
Other
Face
Genital
Defaults to contain ANY selected colors
Discontinued Hand Carved Organic Designs by Maya Jewelry
LAST CHANCE
75% OFFSavings: Retail
Qty
Sold as a PAIR
$ USD
You can appreciate the attention to detail when you wear these hand carved organic designs, each piece is unique and gives you a unique look.

  • Flourish Design pieces are all approximately 2" tall and 1" wide.
  • Huitchol Design pieces are approximately 3-1/8" tall and 3/4" wide in sizes 12g through 8g.  They are 4" tall and 3/4" wide in 6g through 2g.
  • Rooster Design pieces are approximately 1-3/4" tall and 7/8" wide in sizes 14g through 8g.  They are  2-3/4" tall and 1" wide in 6g through 2g.
  • Each Taka Design piece measures approximately 1-13/16" tall.
  • Bloom Design pieces are approximately 2-5/8" tall in sizes 14g through 8g, and 3" tall in 6g through 2g.
  • Feather Design pieces are all approximately 2" tall and 1" wide.
  • Scimitar Design pieces are all approximately 3-5/16" tall and 1" wide.
  • Go-Vin-Da Design pieces are approximately 3-3/4" tall and 1-3/8" wide.
  • Madre Design pieces are approximately 3" tall and 1" wide.
  • Aum My God Design pieces measure approximately 1-1/2" tall in sizes 14g through 8g, 2-1/8" tall in 6g through 2g, and 2-3/8" in sizes 0g and 00g.

All ornate organic designs, especially those in smaller sizes, are quite fragile. We encourage you to handle them with care.

Maya has discontinued most of its organic line. The pieces remaining in our inventory are the last that we will be able to receive. They are first rate in quality and once they are gone, they are gone forever. Get them while you can!

PLEASE NOTE: This item is crafted from organic material and the gauge can vary +/- up to 0.5mm
In our drop-down menus for adding to cart, we show the gauge of the item you are ordering, then the length/diameter, then the ball size if it has any:

Jewelry is measured through a gauge system (conversion chart below). The higher the gauge number the smaller the wire is. For reference, a standard "earring" is usually 20 gauge. Jewelry gauges can vary between manufacturers. There is no universal regulation on companies to make a standard size in body jewelry. This is because some jewelry is made outside of the USA and measured in millimeters. And in the USA jewelry is measured in inches.

GAUGE CONVERSION CHART:
Gauge Millimeter Inch
20g .81mm
18g 1mm
16g 1.2mm 3/64"
14g 1.6mm 1/16"
12g 2mm 5/64"
10g 2.4mm 3/32"
9g 2.7mm
8g 3.2mm 1/8"
7g 3.5mm
6g 4mm 5/32"
4g 5mm 3/16"
5g 4.5mm
2g 6mm 1/4"
1g 7mm
0g 8mm 5/16"
00g 9mm to 10mm 3/8"
  11mm 7/16"
  13mm 1/2"
  14mm 9/16"
  16mm 5/8"
  19mm 3/4"
  22mm 7/8"
  25mm 1"
Show sizes above 1 inch

Rings

Rings are an essential item that can be worn in many piercings. They come in various styles:
  • Captive bead rings - These use tension to hold a bead in place.
  • Clickers - These use a hinge to open and close the ring.
  • Segment rings - These have a "segment" that comes completely out of the jewelry similar to removing a bead. But it looks like a completely seamless piece of jewelry.
  • Seamless rings - These rings require bending to open & close.
How to measure rings
  • Gauge - This is the thickness of the ring itself.
  • Diameter/Length - Measure directly across the inside center of the ring.

Straight Barbells

Straight barbells are commonly worn in various ear projects, nipples, and tongue piercings.
How to measure straight barbells
  • Gauge - This is the thickness of the post/bar itself.
  • Length - Measure directly across the post between the ends.

Double Flare Plugs / Eyelets / Gauges

Commonly worn in earlobes, but can be worn in other stretched piercings.
How to measure double flare plugs
  • Gauge - Measure the size of the plug across the middle.
  • Wearable area - Measure straight across the side of the plug between where the flares start.
  • Flare size / rise - Measure the distance from the side of the plug to where the flare ends.

Single Flare Plugs / Eyelets / Gauges

Commonly worn in earlobes, but can be worn in other stretched piercings.
How to measure single flare plugs
  • Gauge - Measure the size of the plug across the middle.
  • Wearable area - Measure straight across the side of the plug between where one flare starts and where the o-ring starts.
  • Flare size / rise - Measure the distance from the side of the plug to where the flare ends. (see image of double flare plugs)

No Flare Plugs / Eyelets / Gauges

Commonly worn in earlobes, but can be worn in other stretched piercings.
How to measure no flare plugs
  • Gauge - Measure the size of the plug across the middle.
  • Wearable area - Measure straight across the side of the plug between the o-rings.

Teardrop Shaped Plugs

Worn in earlobes
How to measure teardrop shaped jewelry
  • Gauge - Add the height + width and then divide by 2. Then use the conversion chart to get the closest gauge.
  • Wearable area - Measure directly across the plug between where the flares begin.
  • Flare size / rise - Measure from between the flares to the edge of where the flares end.

Curved Barbells

Curved barbells are commonly worn in various ear projects & eyebrows.
How to measure curved barbells
  • Gauge - This is the thickness of the post/bar itself.
  • Length - Measure directly across the post between the ends.

Circular Barbells

Circular barbells are commonly worn in various ear projects, septums, nipples, and lips.
How to measure circular barbells
  • Gauge - This is the thickness of the post itself.
  • Diameter/Length - Measure directly across the inside center of the circular.
JEWELRY THREADING TYPES

Externally threaded

Internally threaded

Threadless
SIZE COMPARISON GUIDES
Enlarged example of 1" on ruler
Ruler example
Customer Photos
Customers Also Bought
Customer Reviews (24)